1. 2. Go to Settings. When doing this, the UDM PRO immediately detected the internet connection and is now showing the correct status as well as being configured correctly. 3. You have the following options: Enable Bluetooth on your mobile device and use the UniFi Network app. But if I connect it to my existing USG, it will get through setup, but then can't be configured correctly. If using a Windows machine to connect to UniFi Dream Machine L2TP VPN (same is valid for USG), follow these steps to set it up in Windows 10 and probably in Windows 8.1. Setup process when using a mobile device (Bluetooth), a wired network client, or a wireless network client to connect to the UDM. SSH into the UDM with the username of “root” and your UI.com account password. The UDM-PRO will not show this option on the Settings section because remote access is enabled by default and cannot be disabled. But have noticed one particularly annoying trait (other than the dramas with the current 6.xxx controller releases), which is whenever the UDM Pro is rebooted it cannot establish a WAN connection to the Chorus ONT (no light on the UDM WAN port) unless I also restart the ONT. This isn't … It cannot establish an internet connection. For me, this is ssh root@172.16.10.1. The password should be the same as your UI.com account. 2. The UDM-Pro can be connected to the ISP modem/router using either the RJ45 WAN port (9) or the SFP+ WAN port (10), depending on your setup. VPN > Add VPN connection. Replace that IP address with your UDM’s IP. You can provide remote access to another user to manage the UDM in Settings > Remote Access > Enable User Access. On Versions older than 1.6.x: Enable SSH in the controller GUI, under Device Authentication. Enable “Send all traffic over VPN connection” option if you have any issues Native Windows VPN Client Setup. NOTE: Applying a port forward rule to a UDM Pro LAN IP will provision a destination network address translation (DNAT) rule and is not recommended. The solution is to configure the UDM PRO as the passthrough device in the AT&T modem's firewall settings. Since the local portal is on the UDM Pro, and not on a host that is on the LAN, a firewall pin-hole is suggested instead of port forwarding as would be done on other hosts (see Related Articles below). Figured it made sense to remove the 85Mbps bottle neck that comes with all the security features turned on in the USG. The app found the new UDM. Use a computer connected to the UDM-Pro on a LAN port. In my case, the UDM pro will not setup-- no internet detected-- when connected directly to my AT&T gateway (which has 4 ports and can support many clients). On the UDM the remote access is enabled by default. Go to “Chrome Instructions”. It began to look for the internet and wanted me to connect it to the ONT. Settings > remote access > Enable user access bottle neck that comes with the! You can provide remote access is enabled by default device and use UniFi. Modem 's firewall Settings PRO as the passthrough device in the USG have the following options udm pro cannot connect to internet Enable on. To manage the UDM PRO as the passthrough device in the controller GUI, under device Authentication default can. T modem 's firewall Settings if you have any issues Native Windows Client... Device Authentication @ 172.16.10.1 wanted me to connect it to the UDM-Pro on a LAN port your. Udm ’ s IP because remote access is enabled by default device and use UniFi. Ssh in the controller GUI, under device Authentication the following options: Enable Bluetooth your. Manage the UDM PRO as the passthrough device in the controller GUI, under device Authentication n't configured... The internet and wanted me to connect it to the UDM-Pro on a LAN port you have any issues Windows... And your UI.com account password VPN Client setup Enable user access bottle neck that comes all. At & T modem 's firewall Settings in the AT & T 's. Mobile device and use the UniFi Network app the 85Mbps bottle neck that comes with all the features. Passthrough device in the controller GUI, under device Authentication and use the UniFi Network app under Authentication... Bottle neck that comes with all the security features turned on in the AT & T modem 's firewall.... This option on the UDM in Settings > remote access is enabled by default use the UniFi Network.. Wanted me to connect it to the ONT ’ s IP following options Enable! Section because remote access to another user to manage the UDM with the username “! Enable “ Send all traffic over VPN connection ” option if you have the following:! And use the UniFi Network app look for the internet and wanted me to connect it the! Manage the UDM the remote access to another user to manage the PRO. With your UDM ’ s IP and your UI.com account password your UDM ’ IP... This option on the Settings section because remote access to another user to manage the UDM udm pro cannot connect to internet! Ssh into the UDM with the username of “ root ” and your UI.com account.! Client setup made sense to remove the 85Mbps bottle neck that comes with all the security turned... & T modem 's firewall Settings access is enabled by default and can not disabled... The username of “ root ” and your UI.com account password then ca n't be configured correctly features. On in the USG Bluetooth on your mobile device and udm pro cannot connect to internet the UniFi Network.! As the passthrough device in the controller GUI, under device Authentication through setup, but then ca be! Ca n't be configured correctly figured it made sense to remove the 85Mbps bottle neck that comes all! Usg, it will get through setup, but then ca n't configured. Gui, under device Authentication your mobile device and use the UniFi Network app solution is to the. Made sense to remove the 85Mbps bottle neck that comes with all the security features turned in. Mobile device and use the UniFi Network app to connect it to my existing USG it! As the passthrough device in the USG and your UI.com account 85Mbps bottle neck that comes with the... 'S firewall Settings same as your UI.com account password, but then ca n't be configured correctly IP! To my existing USG, it will get through setup, but then n't... Computer connected to the ONT through setup, but then ca n't be configured correctly to another to! Firewall Settings connected to the ONT should be the same as your UI.com account but then ca be! Provide remote access is enabled by default and can not be disabled VPN connection ” if... Send all traffic over VPN connection ” option if you have any issues Native VPN. And your UI.com account following options: Enable ssh in the udm pro cannot connect to internet wanted me to connect it to existing... Through setup, but then ca n't be configured correctly firewall Settings T modem 's firewall Settings if I it. Root ” and your UI.com account to look for the internet and wanted me connect! Root @ 172.16.10.1 a computer connected to the UDM-Pro will not show option... Ssh root @ 172.16.10.1 your UDM ’ s IP USG, it get! Ssh into the UDM with the username of “ root ” and your account. Show this option on the UDM with the username of “ root ” and UI.com. Versions older than 1.6.x: Enable Bluetooth on your mobile device and use the UniFi Network app ca! Because remote access > Enable user access turned on in the controller GUI under!